# What's the Best Way for Logistics Operators to Speed Up Dimensioning?

> Speed up dimensioning by measuring at the freight: a LiDAR app replaces the tape and the arithmetic, while fixed hardware suits steady volume through one dock.

Published: 2026-11-16
Source: https://blog.freightsizer.ai/what-s-the-best-way-for-logistics-operators-to-speed-up-dimensioning-70jkc8

---

Stop walking a tape around each handling unit and typing the numbers in: measure at the freight with a tool that also does the arithmetic. The change you can make fastest is a mobile tool such as a LiDAR app on an iPhone or iPad, because nothing is installed on the dock and the reading happens wherever the freight stands.

Fixed hardware makes sense mainly when steady volume already passes one point in the building.

The reading is only one step in the job, so the right choice depends on where your freight sits and what you do with the number. Below are the five realistic options, what each one actually speeds up, and where each one stops working.

## Where does the time in dimensioning actually go?

On the reading and on every step around it. [NMFTA's FAQ on the 2025 NMFC changes](https://nmfta.org/wp-content/media/2024/11/1106-FAQ_Doc-3.pdf) sets out the method: multiply the greatest straight-line length, width and height in inches, including all projections, as tendered to the carrier, then divide by 1,728. It also quotes NMFC Item 110, under which a multi-unit shipment has its density calculated on each handling unit, unless the shipping papers show only a total weight.

So a three-pallet shipment means nine readings, three weights and three density calculations. Around those sit four costs that a faster sensor does not remove by itself:

- **Travel.** The freight moves to the measuring point, or a person moves to the freight.

- **Transcription.** Numbers are written down, then keyed into a WMS, TMS or bill of lading.

- **Arithmetic.** Cube, density and class are worked out as separate steps.

- **Rework.** A pallet measured before wrapping, or with its overhang missed, gets measured again or corrected by the carrier.

Rework is why you cannot trade accuracy for speed. [NMFTA's density guidance of 19 June 2025](https://nmfta.org/news/decoding-density-the-freight-factor-you-cant-afford-to-overlook/) puts 12 to under 15 pounds per cubic foot (pcf) at class 85, and 10 to under 12 pcf at class 92.5. On an item rated on that scale, a 650 lb pallet measured at 48 x 40 x 48 inches is 53.33 cubic feet, or 12.19 pcf, which is class 85. At 49 inches tall it is 54.44 cubic feet, or 11.94 pcf, which is class 92.5. The same guidance lists dimensioners less accurate than the carrier's among the mistakes it sees from shippers, so check a tool's tolerance before you compare its speed.

## When is a tape measure still good enough?

A tape costs almost nothing and works on any freight, in any location. A trained person can look at a crate with a bracket sticking out and see which projection is the greatest. If you ship a few pallets a week and one careful person measures them all, there is little to speed up.

It stops working when volume rises or measuring spreads across shifts. Every reading depends on the person, every number is keyed by hand, and nothing proves what was measured. You can still cut time without buying anything: a marked spot beside the scale, a rule that freight is measured only after wrapping, and one place to record the numbers. Our guide to [setting up a pallet measurement workflow](https://blog.freightsizer.ai/how-should-warehouse-teams-set-up-a-pallet-measurement-workflow-x5r5e6) covers those rules. That cuts travel and rework, but not transcription.

## What does a LiDAR app on an iPhone or iPad speed up?

[FreightSizer](https://freightsizer.ai) measures freight dimensions with LiDAR, calculates density and determines LTL freight class in line with NMFTA guidelines, including the NMFC standards effective 19 July 2025. Its site lists pallets, parcels and irregular shapes and describes seconds from scan to freight class, so time it on your own freight. What it speeds up is the walk to a station and the separate arithmetic, because the operator goes to the freight and gets cube, density and class in one tool. Nothing has to be installed on the dock. On its site, XLSX export comes with the app, and ERP, WMS and TMS integration is quoted per company, which is what decides how much of the transcription step goes away.

It has limits. It needs one of the [iPhone and iPad models with LiDAR](https://blog.freightsizer.ai/which-iphone-and-ipad-models-can-measure-freight-with-lidar-ll9b75), someone still goes to each handling unit, and a sensor that reads size does not read weight, so a scale stays in the process. The site puts typical error at 0.5 to 1 inch, so the same check near a density break applies here too.

## When does a fixed overhead dimensioner make sense?

When steady volume already passes one point in the building and you can route freight under it. The reading then shrinks to the unit's update cycle instead of a walk around the pallet. How much that saves overall depends on your dock, because the published figures are vendor specifications, not independent tests or side-by-side timings. Spec sheets describe up to three operating modes, and the cycle time depends on which one you run:

- **Drop and clear.** The forklift stops, sets the freight down and reverses away before the unit is triggered.

- **Stop and go.** The forklift stops under the unit with the freight still on the forks.

- **In-motion.** The forklift does not stop, and triggering is automatic.

Read the size limits next to those modes, because a faster mode can carry a lower limit, and long freight then falls back to the slowest one. Faster modes and accessories can also be paid options, and prices are often by quote, so ask for a quote on the whole configuration.

The main limit is that it is one point in the building. Everything has to pass under it, which can form a queue at peak, and freight measured in a trailer or at a customer's dock gets nothing from it. In its favor, a fixed unit can carry an NTEP type approval, which matters if you bill from the numbers: [NIST Handbook 44, Section 5.58](https://www.nist.gov/system/files/documents/2025/12/30/5-58-26-HB44-20251209.pdf), applies to devices that determine dimensions or volume for calculating freight, storage or postal charges.

## Can forklifts measure freight as they lift it?

Forklift-mounted systems aim to, and that removes the trip to a station altogether. Sensors on the truck capture length, width and height as the operator picks the freight up.

Three things limit them. At least some are still offered as pilots, so ask what is actually available rather than planning a rollout around a product page. Each truck becomes a measuring device, which makes fleet size part of the decision. And as the worked example above shows, one inch can decide the class of a pallet sitting near a density break, so test the tolerance on your own freight.

## Do handheld computers work for LTL freight?

Mostly for parcels. Handheld mobile computers with a built-in depth sensor capture a carton with a click, with no extra attachment or fixed station. They are built around parcel sizes, so check the listed size range against a 48 x 40 pallet before you consider one. They suit cartons and loose pieces. Check too whether the version you are offered is certified, if you plan to bill from it.

## Which option fits your operation?

Option
Where the reading happens
What it speeds up
Main limit
Fits best

Tape and floor scale
Anywhere
Nothing, but it costs almost nothing
Varies by person and shift, hand keying
Low volume, odd freight

LiDAR app (FreightSizer)
At the freight, wherever it is
The walk to a station and the arithmetic
LiDAR device needed, one unit at a time, scale still needed
Freight spread across doors, lanes or sites, replacing a tape

Fixed overhead dimensioner
One point under the unit
The reading itself, for freight routed under it
All freight must pass that point; size limits by mode
Steady volume through one dock, billing from dimensions

Forklift-mounted system
On the forks, at pickup
The trip to a station
Availability; every truck needs equipping
Forklift-heavy flows open to a pilot

Handheld computer with depth sensor
Wherever the parcel is
Measuring single cartons
Parcel sizes, not pallets
Parcels and cartons

Three questions settle most decisions. Does the freight pass one point, or is it scattered? Is it parcels, pallets or long freight? And do you charge customers from the number, or use it to get your own class right before tender? If you invoice from it, read [whether you need certified dimensioning equipment](https://blog.freightsizer.ai/do-you-need-certified-dimensioning-equipment-for-billing-in-2026-understanding-ltl-freight-class-requirements-273wp7) before choosing. Two tools can be the right answer: a fixed unit on the main dock and a mobile one for whatever never passes it.

Before buying, run your own test. Time 20 handling units from "freight arrives" to "numbers in the system" for each method, on real freight at your busiest hour, then check the same units by hand. That gives you a full cycle time, a figure vendor specifications do not contain.

## What slows teams down after the tool arrives?

- **Measuring too early.** NMFTA's method measures freight as tendered, and its guidance names forgotten pallet or packaging height as a common error. Measure after wrapping, with everything on it.

- **Leaving data entry manual.** Keying readings from a screen keeps the transcription step. Our article on [getting mobile dimensioning data into a WMS or TMS](https://blog.freightsizer.ai/how-to-get-mobile-dimensioning-data-into-your-wms-or-tms-without-a-custom-integration-oamv2a) covers ways around it.

- **Separating size from weight.** Density needs both, so put the scale where you measure. A scale at the far end of the dock only moves the queue.

- **Sending oversize freight through the fast lane.** Set a rule for what goes to drop and clear before peak, not during it.

- **Reusing old numbers.** NMFTA lists default dimensions from old records among the errors it sees, and a fast tool does not help if nobody uses it on repeat freight.

## Frequently Asked Questions

**What is the fastest way to dimension pallets?**

It depends on where the freight is. For freight spread across doors, lanes or sites, measuring at the pallet with a LiDAR app avoids the trip to a station. For freight that passes one point, in-motion capture looks fastest on vendor specifications, but only for freight inside that mode's size limit, on routes that pass under the unit. Time the full cycle on your own freight before deciding.

**Can an iPhone or iPad replace a dimensioner?**

For measuring your own freight before tender, an app such as FreightSizer can take the place of a tape measure and dedicated dimensioning hardware on a LiDAR-equipped device. If the number is the basis of a customer invoice, check the certification question first. You still need a scale for the weight.

**Should we measure every handling unit or only a sample?**

Measure every handling unit on density-rated freight. NMFC Item 110, as quoted by NMFTA, calculates density per handling unit unless the papers show only a total weight, and a sample cannot tell you the size of the next pallet. Repeat freight with identical packaging is the only place where stored dimensions are defensible, and those still need regular checks.

**How should we compare vendor speed claims?**

Treat a seconds figure as the sensor's time, not your cycle time. Positioning, scanning the ID, weighing and getting the data into your system all sit around it. Time the full cycle on your own freight before comparing tools.