# How Long Does It Take to Scan and Classify a Pallet?

> The capture takes seconds, a fixed-station cycle 40-60 seconds by one maker's rate, and a manual class lookup 10 minutes or more. Time your own dock.

Published: 2026-11-21
Source: https://blog.freightsizer.ai/how-long-does-it-take-to-scan-and-classify-a-pallet-pwo1wg

---

The capture itself takes seconds: [one maker of fixed pallet dimensioners](https://vmeasure.ai/static-pallet-dimensioning-system/) quotes about 2 seconds, and [FreightSizer's App Store listing](https://apps.apple.com/us/app/id6738141881) describes measuring dimensions, calculating density and determining freight class "in seconds". The whole job runs longer: the same maker's rate of 60-90 pallets an hour works out to 40 to 60 seconds a pallet, and [C.H. Robinson says](https://www.fleetowner.com/technology/article/55299908/ch-robinson-launches-ai-agent-for-national-motor-freight-classification-system) a manual freight class and code lookup "can easily take a person 10 minutes or more per shipment".

## What counts as "scan and classify"?

Five jobs sit inside that phrase, and only one of them is the scan:

- **Bring the pallet and the tool together.** Freight travels to a fixed station, or a handheld device travels to the freight.

- **Capture length, width and height.** This is the step vendors put a number on.

- **Get the weight.** Density is weight divided by cubic feet, so dimensions alone give you volume and nothing more.

- **Turn the numbers into a class.** The density arithmetic is instant. Confirming which NMFC item the commodity falls under is not always.

- **Record the result.** The numbers have to reach the bill of lading, and the same figures should sit in your WMS or TMS.

When someone quotes you a time, ask which of these five it covers. A figure for step 2 tells you how fast the sensor is. It says little about how many pallets leave the dock in an hour.

If you are building this into a dock routine, [How Should Warehouse Teams Set Up a Pallet Measurement Workflow?](https://blog.freightsizer.ai/how-should-warehouse-teams-set-up-a-pallet-measurement-workflow-x5r5e6) covers where each step belongs.

## How long does a fixed pallet dimensioner take?

About 2 seconds for the reading. vMeasure's [static pallet dimensioning page](https://vmeasure.ai/static-pallet-dimensioning-system/) says "under 2 seconds" in its introduction and gives 2-3 seconds as the dimensioning time in its specification table.

The more useful planning figure on that page is its headline rate of 60-90 pallets per hour. That works out to one pallet every 40 to 60 seconds, so the reading is a small share of the cycle. The rest is everything around it: getting the pallet into the measuring zone, clearing it out and dealing with the result. The same page also says the system "cuts pallet processing time from 3 minutes to 30 seconds".

Treat all of these as the maker's own figures. We did not find a published independent time study of pallet dimensioning, so the number to plan around is one from your own dock.

A fixed unit gains the most when several steps happen in one place. vMeasure describes mounting its system over the stretch wrapper, so the pallet is measured as soon as wrapping is complete, and [ArcBest](https://arcb.com/blog/measuring-cubic-feet-for-ltl-shipments) notes that some systems also include weight verification, "giving you a full density calculation in one step".

## How long does a phone or tablet scan take?

The App Store listing's answer is "in seconds", for measuring, density and class together. It gives no stopwatch figure, so read it as the capture and calculation steps rather than as a full cycle per pallet.

A handheld tool changes where the time goes more than it changes the reading. The device goes to the pallet, so there is no trip to a station and no queue at one during a peak. In exchange, a person holds the device, and the result is only as good as what they capture: the full load, any overhang and any cone on top. Only some iPhones and iPads have a LiDAR sensor, so [check which models can measure freight](https://blog.freightsizer.ai/which-iphone-and-ipad-models-can-measure-freight-with-lidar-ll9b75) before planning devices per lane.

[FreightSizer](https://freightsizer.ai) is one tool of this kind: an iPhone and iPad app that measures freight dimensions with LiDAR, calculates density and determines LTL freight class in line with NMFTA guidelines.

Here is how the three common methods compare on time:

Tape measure and scale
Fixed dimensioner
Phone or tablet with LiDAR

Capture
A person pulls each dimension by hand
About 2 seconds, as quoted by the maker above
"In seconds", as quoted by the listing above

Moving the freight
To the scale, if the scale is fixed
To the station, unless it sits on the pallet's path, such as over a stretch wrapper
None for the measurement, the device goes to the pallet

Density and class
A separate calculation and lookup
Depends on the software paired with it
Automated in the app, as its listing describes

What slows it down
Tall or irregular loads, retyped numbers
A queue at the station
An incomplete capture and a repeat scan

For the wider trade-offs beyond time, see [Should You Measure Freight Manually or With Automated Dimensioning?](https://blog.freightsizer.ai/should-you-measure-freight-manually-or-with-automated-dimensioning-hklipi)

## Why can classification take longer than the scan?

The arithmetic is the quick part. ArcBest gives the formula: length × width × height in inches, divided by 1,728, gives cubic feet, and weight divided by cubic feet gives density. Its example, a 500 lb pallet at 48 × 40 × 60 inches, comes to 66.67 cubic feet and 7.5 pounds per cubic foot. Any tool does that instantly once it has the inputs.

Two other things take the time.

**The weight.** [NMFTA](https://nmfta.org/standards/classification/) says to "always use accurate measurements for weight and dimensions—never estimates", so the finished pallet needs a real scale reading. If the scale sits beside the measuring point, this barely registers. If the pallet has to travel to it, the trip can outlast the scan many times over.

**The item.** NMFTA says each product or commodity gets a freight class from 50 to 500 based on four characteristics: density, handling, stowability and liability. Density is one input of the four, so someone has to know what the commodity is and how it is listed. NMFTA's ClassIT+ "helps you find the correct NMFC item number, calculate density, and confirm freight class before you ship".

A published figure for this step comes from C.H. Robinson, [quoted by FleetOwner on 30 June 2025](https://www.fleetowner.com/technology/article/55299908/ch-robinson-launches-ai-agent-for-national-motor-freight-classification-system): manually looking up or confirming the freight class and code for every emailed LTL tender "can easily take a person 10 minutes or more per shipment". That is one logistics company's own figure, for tenders where the class and code might be missing or incorrect. For a product you ship every week, the work is done once and saved against the SKU, so a repeat pallet costs almost nothing here. For a new commodity, expect the lookup to take far longer than the scan.

One trap is a class sheet built before the updated NMFC standards took effect on 19 July 2025. It gives a fast answer that may be out of date, so re-check old lookups against the current standard. [Freight Class Lookup vs. Density Calculation](https://blog.freightsizer.ai/freight-class-lookup-vs-density-calculation-navigating-ltl-classification-in-2026-vabr6s) explains how the two approaches differ.

## What slows a scan down on a real dock?

Many delays have little to do with the sensor:

- **The pallet is not finished.** Measure it as it will be tendered. If a carton is added or the wrap is redone afterwards, the numbers no longer describe the freight, and it has to be scanned again.

- **Overhang and cones.** ArcBest's rules include the pallet or skid, product that extends beyond the pallet, and "Do not stack" cones in the height. A capture that misses any of them has to be repeated.

- **Irregular loads.** ArcBest says irregularly shaped freight must use the longest measurement for each side, and that manual measuring of such freight can be "inconsistent or time-consuming".

- **Shrink wrap.** vMeasure's page lists colored and transparent shrink wrap among the pallet types it shows, so wrap is a case worth testing. Include wrapped pallets, dark film among them, in any trial of an optical tool, fixed or handheld.

- **Retyping.** A number copied by hand onto the bill of lading is one more step to wait for and one more place for an error to enter.

## Is a faster scan worth it if the number is wrong?

No. NMFTA warns that if you misclassify freight, "you could face reclassification charges, delays, or damage", and ArcBest notes that if incorrect measurements are entered in its online quote, "your price is subject to change". Any seconds saved on the dock disappear the first time an invoice has to be disputed.

A small miss shows why. Take ArcBest's pallet and add 2 inches of overhang along the length that nobody measured. The true size is 50 × 40 × 60 inches, about 69.44 cubic feet, and the same 500 lb comes to about 7.2 pounds per cubic foot rather than 7.5. That difference will not change the class of every pallet, but near a density breakpoint it can.

So judge a method by how long it takes to reach a number you would defend.

## How do you find your own time per pallet?

Time it, because no published figure covers your freight, your dock and your paperwork.

- Choose a normal shift and a mix of pallets, including the awkward ones: irregular loads, dark film, tall stacks.

- Start the clock when the pallet is finished and stop it when the numbers are on the bill of lading.

- Log the five jobs separately, not one total.

- Run the same pallets through your current method and through the tool you are testing, and compare the dimensions as well as the times.

- Count repeat scans and carrier corrections, since each one adds time that a per-pallet average hides.

The split tells you what to fix. If the time goes on moving freight, a device that goes to the pallet, or a station on the pallet's existing path, helps. If it goes on item lookups, a saved table of SKUs and NMFC items will do more than a new sensor. If it goes on retyping, fix the data path first.

## Frequently Asked Questions

**Does "in seconds" mean the whole pallet is done in seconds?**

In the figures quoted here it refers to the capture, or to the capture and the calculation. vMeasure's own figures show the gap for a fixed station: a reading of about 2 seconds inside a rate of 60-90 pallets per hour. Finishing, weighing and recording take time beyond the reading.

**Does weight need a separate step?**

Often, yes. Density needs a weight as well as dimensions, and some dimensioning systems include weight verification so that both arrive together. Without that it is a separate scale reading, so keep the scale close to where you measure.

**Can a dimension reading alone decide the freight class?**

Not on its own. NMFTA bases class on density, handling, stowability and liability, and density itself needs the weight. Check the commodity's NMFC item as well, at least the first time it ships, and allow for the lookup: C.H. Robinson puts a manual one at 10 minutes or more per shipment.

**How many pallets can be scanned in an hour?**

The published rate used here is a manufacturer's: vMeasure quotes 60-90 pallets per hour for its static system. Your own rate depends on how far freight travels, how often scans are repeated and how the numbers are recorded, so measure it on a normal shift.